Operator’s Manual
WARNING
Before using this product, read
this manual and follow all Safety
Rules and Operating Instructions.
Questions? Help is just a moment away!
Call: Generac Generator Helpline - 1-800-270-1408 M-F 8-5 CT
Model No. 1019-3 (7,500 Watt AC Generator) Manual No. 189713GS Revision 11 (12/15/2005)
7500EXL Extended Life Generator
DANGER
WARNING
Storage batteries give off explosive hydrogen gas
during recharging.
Fuel and its vapors are extremely flammable and
explosive.
Hydrogen gas stays near battery for a long time
after battery has been charged.
Fire or explosion can cause severe burns or
death.
Slightest spark will ignite hydrogen and cause
explosion.
You can be blinded or severely injured.
Battery electrolyte fluid contains acid and is
extremely caustic.
Contact with battery fluid will cause severe
chemical burns.
WHEN ADDING OR DRAINING FUEL
• Turn generator OFF and let it cool at least 2 minutes before
removing fuel cap. Loosen cap slowly to relieve pressure in
tank.
• Fill or drain fuel tank outdoors.
• DO NOT overfill tank.Allow space for fuel expansion.
• Keep fuel away from sparks, open flames, pilot lights, heat, and
other ignition sources.
• DO NOT allow any open flame, spark, heat, or lit cigarette
during and for several minutes after charging a battery.
• DO NOT light a cigarette or smoke.
• Wear protective goggles, rubber apron, and rubber gloves.
WHEN STARTING EQUIPMENT
• Ensure spark plug, muffler, fuel cap and air cleaner are in place.
• DO NOT crank engine with spark plug removed.
• If fuel spills, wait until it evaporates before starting engine.
WARNING
Running generator gives off carbon monoxide,
an odorless, colorless, poison gas.
Breathing carbon monoxide can cause nausea,
fainting or death.
WHEN OPERATING EQUIPMENT
• DO NOT tip engine or equipment at angle which causes fuel
to spill.
• This generator is not for use in mobile equipment or marine
applications.
• Operate generator ONLY outdoors.
• Keep exhaust gas from entering a confined area through
windows, doors, ventilation intakes or other openings.
• DO NOT operate generator inside any building or enclosure
(even if doors or windows are open), including the generator
compartment of a recreational vehicle (RV).
WHEN TRANSPORTING OR REPAIRING
EQUIPMENT
• Transport/repair with fuel tank EMPTY or with fuel shutoff
valve OFF.
• Disconnect spark plug wire.
WARNING
Generator produces powerful voltage.
Failure to isolate generator from power utility
can result in death or injury to electric utility
workers due to backfeed of electrical energy.
WHEN STORING FUEL OR EQUIPMENT WITH FUEL
IN TANK
• Store away from furnaces, stoves, water heaters, clothes
dryers or other appliances that have pilot light or other
ignition source because they can ignite fuel vapors.
WARNING
• This generator does not meet U. S. Coast Guard Regulation
• When using generator for backup power, notify utility
company. Use approved transfer equipment to isolate
generator from electric utility.
• Use a ground circuit fault interrupter (GFCI) in any damp or
highly conductive area, such as metal decking or steel work.
• DO NOT touch bare wires or receptacles.
• DO NOT use generator with electrical cords which are worn,
frayed, bare or otherwise damaged.
33CFR-183 and should not be used on marine applications.
• Failure to use the appropriate U. S. Coast Guard approved
generator could result in bodily injury and/or property
damage.
• DO NOT operate generator in the rain or wet weather.
• DO NOT handle generator or electrical cords while standing
in water, while barefoot, or while hands or feet are wet.
• DO NOT allow unqualified persons or children to operate or
service generator.
3
7500EXL Extended Life Generator
CAUTION
Excessively high operating speeds increase risk of injury
and damage to generator.
WARNING
Rapid retraction of starter cord (kickback) will
pull hand and arm toward engine faster than
you can let go.
Excessively low speeds impose a heavy load.
Broken bones, fractures, bruises or sprains could
result.
• DO NOT tamper with governed speed. Generator supplies
correct rated frequency and voltage when running at governed
speed.
• When starting engine, pull cord slowly until resistance is felt
and then pull rapidly to avoid kickback.
• NEVER start or stop engine with electrical devices plugged in
and turned on.
• DO NOT modify generator in any way.
CAUTION
Exceeding generators wattage/amperage capacity can
damage generator and/or electrical devices connected
to it.
WARNING
Running engines produce heat.Temperature of
muffler and nearby areas can reach or exceed
150°F (65°C).
Severe burns can occur on contact.
Exhaust heat/gases can ignite combustibles,
structures or damage fuel tank causing a fire.
• See “Don’t Overload Generator”.
• Start generator and let engine stabilize before connecting
electrical loads.
• Connect electrical loads in OFF position, then turn ON for
operation.
• DO NOT touch hot surfaces and avoid hot exhaust gases.
• Allow equipment to cool before touching.
• Turn electrical loads OFF and disconnect from generator
before stopping generator.
• Keep at least 5 ft. (152 cm) clearance on all sides of generator
including overhead.
CAUTION
Improper treatment of generator can damage it and
• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and
Public Property require equipment powered by an internal
combustion engine to have a spark arrester, maintained in
effective working order, complying to USDA Forest service
standard 5100-1C or later revision. In the State of California a
spark arrester is required under section 4442 of the California
Public resources code. Other states may have similar laws.
shorten its life.
• Use generator only for intended uses.
• If you have questions about intended use, ask dealer or call
1-800-270-1408.
• Operate generator only on level surfaces.
• DO NOT expose generator to excessive moisture, dust, dirt,
or corrosive vapors.
WARNING
• DO NOT insert any objects through cooling slots.
• If connected devices overheat, turn them off and disconnect
them from generator.
Unintentional sparking can result in fire or
electric shock.
• Shut off generator if:
-electrical output is lost;
WHEN ADJUSTING OR MAKING REPAIRSTOYOUR
GENERATOR
-equipment sparks, smokes, or emits flames;
-unit vibrates excessively.
• Disconnect the spark plug wire from the spark plug and place
the wire where it cannot contact spark plug.
WHENTESTING FOR ENGINE SPARK
• Use approved spark plug tester.
• DO NOT check for spark with spark plug removed.
4
7500EXL Extended Life Generator
KNOWYOUR GENERATOR
Read this Operator’s Manual and safety rules before operating your generator.
Compare this illustration with your generator to familiarize yourself with the locations of various controls and
adjustments. Save this manual for future reference.
Electric Start Button
Oil Fill Cap
Recoil Starter
Circuit Breakers (AC)
Fuel Tank
12Volt DC
Receptacle
Idle Control Switch
Choke Lever
Run/Stop Switch
Air Cleaner
120/240Volt AC,
30 Amp Locking
Receptacle
Spark Arrester Muffler
120Volt AC, 30 Amp
Locking Receptacle
120/240Volt AC,
50 Amp Receptacle
120Volt AC, 20 Amp
Duplex Receptacle
Grounding Fastener
12Volt DC Receptacle — Use this receptacle with
Choke Lever — Used when starting a cold engine.
battery charge cables to charge a 12Volt battery.
Circuit Breakers (AC) — Each receptacle is provided
with a "push to reset" circuit breaker to protect the
generator against electrical overload.
120Volt AC, 20 Amp Duplex Receptacle — May be
used to supply electrical power for the operation of
120Volt AC, single phase, 60 Hz electrical lighting, appliance,
tool and motor loads.
FuelTank — Capacity of seven (7) U.S. gallons.
Electric Start Switch — Press to start the engine.
120Volt AC, 30 Amp Locking Receptacle — May be
used to supply electrical power for the operation of
120Volt AC, 30 Amp, single phase, 60 Hz electrical lighting,
appliance, tool and motor loads.
Grounding Fastener — Consult your local agency having
jurisdiction for grounding requirements in your area.
Idle Control Switch — The idle control runs the engine
at normal (high) speeds when there is a load present and
runs the engine at idle (low) speeds when a load is not
present.
120/240Volt AC, 30 Amp Locking Receptacle — May
be used to supply electrical power for the operation of
120 and/or 240Volt AC, 30 Amp, single phase, 60 Hz
electrical lighting, appliance, tool and motor loads.
Oil Fill Cap — Add oil to engine here.
Recoil Starter — Used to start the engine manually.
120/240Volt AC, 50 Amp Receptacle — May be used
to supply electrical power for the operation of 240Volt AC,
50 Amp, single phase, 60 Hz electrical loads.
Run/Stop Switch — Must be in “Run” position to start
engine. Set to “Stop” to stop a running engine.
Air Cleaner — Protects engine by filtering dust and
debris out of intake air.
Spark Arrester Muffler — Exhaust muffler lowers engine
noise and is equipped with a spark arrester screen.
5
7500EXL Extended Life Generator
• Battery Charge Cables
• Spare Spark Plug,Air Filter, and Oil Filter
• Spark Plug Wrench
• (2) Locking 30 Amp Plugs
• Engine Oil
ASSEMBLY
Your generator requires some assembly and is ready for
use after it has been properly serviced with the
recommended oil and fuel.
• Operator's Manual
• Engine Manual
If any parts are missing or damaged, call the generator
helpline at 1-800-270-1408.
If you have any problems with the assembly of your
generator, please call the generator helpline at
1-800-270-1408.
Unpack the Generator
1. Set the carton on a rigid flat surface.
Install Wheel Kit
The wheel kit is designed to greatly improve the portability
of your generator.
2. Open carton completely by cutting each corner from
top to bottom.
NOTE: Wheel kit is not intended for over-the-road use.
You will need the following tools to install this wheel kit:
• 1/2" or 13mm socket wrench
• 1/2" or 13mm open end wrench
• 7/16" socket wrench
3. Remove everything from carton except generator.
4. Leave generator on carton to install wheel kit.
Carton Contents
Check all contents against those listed below:
• Generator
• 7/16" open end wrench
• Wheel kit
• Pliers
• Storage Cover
• Safety glasses
• Adapter Cord Set
• Battery
• Battery Float Charger
Refer to Figure 1 and install the wheel kit as follows:
1. Tip generator so that engine end is up.
Figure 1 — Install Wheel Kit
Axle
Wheel
Flat Washer
1/4x20 Lock Nut
Support Leg
M8x20mm Capscrew
E-Ring
Vibration Mount
M8 Lock Nut
1/4-20x1” Capscrew
6
7500EXL Extended Life Generator
2. Slide axle through both mounting brackets.
Check Battery / Attach Negative
Battery Wire
The sealed battery on the generator is fully charged and
pre–installed except for the negative (black) battery cable.
3. Slide a wheel over the axle.
NOTE: Be sure to install both wheels with the air
pressure valve on the outboard side.
4. Place a washer on axle and then place an e-ring in axle
groove.
To install:
1. Cut off tie wrap securing loose end of negative (black)
cable.
5. Install e-ring with pliers, squeezing from top of e-ring
to bottom of axle.
2. Remove screw, lock washer and flat washer on
negative battery terminal.
CAUTION
E-rings can cause eye injury.
E-rings can spring back and become airborne
when installing or removing.
3. Slide lock washer, flat washer and negative battery
cable over screw (Figure 2).
Figure 2 — Negative Battery Connection
Negative
Battery Cable
• Always wear eye protection when installing/removing e-rings.
6. Repeat step 3 thru 5 to secure second wheel.
7. Tip generator so that engine side is down.
Screw
8. Attach the vibration mounts to the support leg with
1/4-20 x 1” capscrews and 1/4-20 lock nuts.
9. Line up holes in support leg with holes in generator
frame.
Flat Washer
Lock Washer
Positive
Battery Cable
10. Attach support leg using 2 capscrews (M8 x 20 mm)
and 2 hex nuts (M8).Tighten with a 1/2” or 13mm
socket wrench and 1/2” or 13mm wrench.
4. Reattach screw to negative battery terminal and
tighten.
11. Return generator to normal operating position (resting
on wheels and support leg).
5. Verify that connections to battery and generator are
tight and secure.
12. Check each fastener to ensure it is secure.
7
7500EXL Extended Life Generator
Add Fuel
NOTE: This gasoline engine is certified to operate on
gasoline. Exhaust Emission Control System: EM (Engine
Modifications).
BEFORE STARTINGTHE
ENGINE
Add Engine Oil
WARNING
Fuel and its vapors are extremely flammable and
explosive.
Fire or explosion can cause severe burns or
death.
• Place generator on a level surface.
CAUTION
Any attempt to crank or start the engine before it has
been properly filled with the recommended oil will result
in equipment failure.
WHEN ADDING FUEL
• Turn generator OFF and let it cool at least 2 minutes before
removing fuel cap. Loosen cap slowly to relieve pressure in tank.
• Fill fuel tank outdoors.
• DO NOT overfill tank.Allow space for fuel expansion.
• Keep fuel away from sparks, open flames, pilot lights, heat, and
other ignition sources.
• Refer to engine manual for oil fill information.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
• Refer to engine operator’s manual and follow oil
recommendations and instructions.
• DO NOT light a cigarette or smoke.
NOTE: Check oil often during engine break–in. Refer to
engine operator’s manual for recommendations.
1. Use clean, fresh, regular UNLEADED fuel with a
minimum of 85 octane. DO NOT use fuel which
contains Methanol. DO NOT mix oil with fuel.
NOTE: The generator assembly rotates on a prelubricated
and sealed ball bearing that requires no additional
lubrication for the life of the bearing.
2. Clean area around fuel fill cap, remove cap.
3. Slowly add regular unleaded fuel to fuel tank. Be careful
not to overfill.Allow at least 1.5" of tank space for fuel
expansion (Figure 3).
Figure 3 - Fuel Expansion
Tank
Fuel
4. Install fuel cap and wipe up any spilled fuel.
8
7500EXL Extended Life Generator
Generator Location
Generator Clearance
USINGTHE GENERATOR
System Ground
WARNING
Exhaust heat/gases can ignite combustibles,
structures or damage fuel tank causing a fire.
The generator has a system ground that connects the
generator frame components to the ground terminals on
the AC output receptacles.The system ground is connected
to the AC neutral wire (see “Equipment Description”,
earlier in this manual).
• Keep at least 5 ft. (152 cm) clearance on all sides of generator
including overhead.
Place generator in a well ventilated area, which will allow
for removal of deadly exhaust gas. DO NOT place
generator where exhaust gas could accumulate and enter
inside or be drawn into a potentially occupied building.
Ensure exhaust gas is kept away from any windows, doors,
ventilation intakes or other openings that can allow exhaust
gas to collect in a confined area (Figure 4). Prevailing winds
and air currents should be taken into consideration when
positioning generator.
Special Requirements
There may be Federal or State Occupational Safety and
Health Administration (OSHA) regulations, local codes, or
ordinances that apply to the intended use of the generator.
Please consult a qualified electrician, electrical inspector, or
the local agency having jurisdiction.
• In some areas, generators are required to be registered
with local utility companies.
WARNING
Running generator gives off carbon monoxide,
an odorless, colorless, poison gas.
• If the generator is used at a construction site, there may
be additional regulations which must be observed.
Connecting to a Building’s Electrical
System
Connections for standby power to a building’s electrical
system must be made by a qualified electrician.The
connection must isolate the generator power from utility
power, and must comply with all applicable laws and
electrical codes.
Breathing carbon monoxide can cause nausea,
fainting or death.
• Operate generator ONLY outdoors.
• Keep exhaust gas from entering a confined area through
windows, doors, ventilation intakes or other openings.
• DO NOT operate generator inside any building or enclosure
(even if doors or windows are open), including the generator
compartment of a recreational vehicle (RV).
WARNING
Generator produces powerful voltage.
Figure 4 — Generator Clearance
Failure to isolate generator from power utility
can result in death or injury to electric utility
workers due to backfeed of electrical energy.
• When using generator for backup power, notify utility
company. Use approved transfer equipment to isolate
generator from electric utility.
• Use a ground fault circuit interrupter (GFCI) in any damp or
highly conductive area, such as metal decking or steel work.
• DO NOT touch bare wires or receptacles.
Typical Generator Shown
• DO NOT use generator with electrical cords which are worn,
frayed, bare or otherwise damaged.
• DO NOT operate generator in the rain.
• DO NOT handle generator or electrical cords while standing
in water, while barefoot, or while hands or feet are wet.
• DO NOT allow unqualified persons or children to operate or
service generator.
Exhaust Port
9
7500EXL Extended Life Generator
NOTE: If engine starts after 3 pulls but fails to run, or if
OPERATINGTHE
GENERATOR
unit shuts down during operation, make sure unit is on a
level surface and check for proper oil level in crankcase.
This unit may be equipped with a low oil protection device.
See engine manual.
Starting the Engine
WARNING
Running engines produce heat.Temperature of
muffler and nearby areas can reach or exceed
150°F (65°C).
IMPORTANT: Always unplug the battery float charger
before starting the generator.
Disconnect all electrical loads from the generator. Use the
following start instruction steps by numerical order:
Severe burns can occur on contact.
Exhaust heat/gases can ignite combustibles,
structures or damage fuel tank causing a fire.
1. Make sure unit is on a level surface.
IMPORTANT: Failure to start and operate unit on a level
surface will cause the unit not to start or shut down during
operation.
• DO NOT touch hot surfaces and avoid hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 5 ft. (152 cm) clearance on all sides of generator
including overhead.
2. Turn the fuel valve to the “On” position (Figure 5).The
fuel valve handle should be vertical (pointing toward
the ground) for fuel to flow.
• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and
Public Property require equipment powered by an internal
combustion engine to have a spark arrester, maintained in
effective working order, complying to USDA Forest service
standard 5100-1C or later revision. In the State of California a
spark arrester is required under section 4442 of the California
Public resources code. Other states may have similar laws.
Figure 5 — FuelValve
FuelValve is shown
in the On position
Connecting Electrical Loads
• Let engine stabilize and warm up for a few minutes after
starting.
3. Make sure the Idle Control switch is in “Off” position
(Figure 6).
Figure 6 — Idle Control Switch
• Plug in and turn on the desired 120 and/or 240 Volt AC,
single phase, 60 Hz electrical loads.
• DO NOT connect 240Volt loads to the 120Volt
receptacles.
• DO NOT connect 3–phase loads to the generator.
• DO NOT connect 50 Hz loads to the generator.
• DO NOT OVERLOADTHE GENERATOR. See
“Don’t Overload Generator”.
4. Start the engine according to instructions given in the
engine operator’s manual.
CAUTION
Exceeding generators wattage/amperage capacity can
damage generator and/or electrical devices connected
to it.
WARNING
Rapid retraction of starter cord (kickback) will
pull hand and arm toward engine faster than
you can let go.
Broken bones, fractures, bruises or sprains could
result.
• See “Don’t Overload Generator”.
• Start generator and let engine stabilize before connecting
electrical loads.
• Connect electrical loads in OFF position, then turn ON for
operation.
• When starting engine, pull cord slowly until resistance is felt
and then pull rapidly to avoid kickback.
• Turn electrical loads OFF and disconnect from generator
before stopping generator.
• NEVER start or stop engine with electrical devices plugged in
and turned on.
10
7500EXL Extended Life Generator
To recharge 12Volt batteries, proceed as follows:
Stopping the Engine
1. Turn off and unplug all electrical loads from generator
panel receptacles. NEVER start or stop engine with
electrical devices plugged in and turned on.
1. Check fluid level in all battery cells. If necessary, add
ONLY distilled water to cover separators in battery
cells. DO NOT use tap water.
2. If battery is equipped with vent caps, make sure they
are installed and are tight.
2. Put idle control switch in “Off” position.
3. Let engine run at no–load for 30 seconds to stabilize
internal temperatures of engine and generator.
3. If necessary, clean battery terminals.
4. Connect battery charge cable connector plug to panel
receptacle identified by the words “12-VOLTS D.C.”
4. Turn engine off according to instructions given in
engine operator’s manual.
5. Connect battery charge cable clamp with red handle
to the positive (+) battery terminal (Figure 7).
5. Move fuel valve to “Off” position.
Figure 7 — Battery Connections
Operating Automatic Idle Control
This switch is designed to greatly improve fuel economy.
When this switch is turned ON, the engine will only
run at its normal high governed engine speed when an
electrical load is connected.When an electrical load is
removed, the engine will run at a reduced speed. With the
switch off, the engine will run at the normal high engine
speed. Always have the switch off when starting and
stopping the engine.
Charging a Battery
6. Connect battery charge cable clamp with black handle
to the negative (–) battery terminal (Figure 7).
Your generator has the capability of recharging a discharged
12Volt automotive or utility style storage battery. DO
NOT use the unit to charge any 6Volt batteries. DO NOT
use the unit to crank an engine having a discharged battery.
7. Start engine. Let engine run while battery recharges.
8. When battery has charged, shut down engine
NOTE: Use an automotive hydrometer to test battery
state of charge and condition. Follow the hydrometer
manufacturer’s instructions carefully. Generally, a battery is
considered to be at 100% state of charge when specific
gravity of its fluid (as measured by hydrometer) is 1.260 or
higher.
DANGER
Storage batteries give off explosive hydrogen gas
during recharging.
Hydrogen gas stays near battery for a long time
after battery has been charged.
Slightest spark will ignite hydrogen and cause
explosion.
You can be blinded or severely injured.
Battery electrolyte fluid contains acid and is
extremely caustic.
Contact with battery fluid will cause severe
chemical burns.
• DO NOT allow any open flame, spark, heat, or lit cigarette
during and for several minutes after charging a battery.
• Wear protective goggles, rubber apron, and rubber gloves.
11
7500EXL Extended Life Generator
How to Use the Battery Charger
Use battery float charger jack to keep the starting battery
charged and ready for use. Battery charging should be done
in a dry location, such as inside a garage.
COLD WEATHER
OPERATION
Under certain weather conditions (temperatures below
40°F [4°C] combined with high humidity), your generator
may experience icing of the carburetor and/or the
crankcase breather system.To reduce this problem, you
need to perform the following:
• Plug the charger into the unit’s “Battery Float Charger”
jack, which is located on the starter switch (Figure 8).
Plug battery charger into a 120Volt AC wall receptacle.
Figure 8 — Battery Charger Jack
1. Make sure generator has clean, fresh fuel.
2. Open fuel valve (turn valve to open position).
3. Use SAE 5W-30 oil (synthetic preferred, see engine
operator’s manual).
4. Check oil level daily or after every eight (8) hours of
operation.
5. Maintain generator following “Maintenance Schedule”
in engine operator’s manual.
• Unplug the charger from the unit and the wall outlet
when generator is being started and while it is in
operation.
6. Shelter unit from elements.
• Keep this charger plugged in when generator is not in
use to prolong battery life.The charger has a built in float
equalizer and will not overcharge the battery, even when
plugged in for an extended period of time.
IMPORTANT: See “Battery Maintenance” on page 17 for
additional information.
12
7500EXL Extended Life Generator
6. Start generator as described in the section “Starting
Creating aTemporary Shelter
the Engine”, then place carton over generator. Keep at
least 5 ft. (152 cm) clearance on all sides of generator
including overhead with shelter in place.
1. In an emergency, use the original shipping carton.
2. Cut off top carton flaps and one long side of carton to
expose muffler side of unit. If required, tape up other
sides of carton to fit over generator as shown in
Figure 9.
WARNING
Running engines produce heat.Temperature of
muffler and nearby areas can reach or exceed
150°F (65°C).
Figure 9 — Permanent Cold Weather Shelter
Wind
Severe burns can occur on contact.
Exhaust heat/gases can ignite combustibles,
structures or damage fuel tank causing a fire.
• DO NOT touch hot surfaces and avoid hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 5 ft. (152 cm) clearance on all sides of generator
including overhead.
• Remove shelter when temperatures are above 40°F [4°C].
7. Remove shelter when temperatures are above 40°F
[4°C].
NOTE: If required, remove wheel kit to fit carton over
generator as shown in Figure 9.
8. Turn engine OFF and let cool two (2) minutes before
refueling.Wipe up any spilled fuel.
3. Cut appropriate slots to access receptacles of unit.
4. Face exposed end away from wind and elements.
Creating a Permanent Shelter
5. Locate generator as described in the section
“Generator Location”. Keep exhaust gas from entering
a confined area through windows, doors, ventilation
intakes or other openings.
1. Build a structure that will enclose three sides and the
top of the generator, making sure muffler side of
generator is exposed.
NOTE: Structure should hold enough heat created by the
generator to prevent icing problem.
WARNING
Running generator gives off carbon monoxide,
an odorless, colorless, poison gas.
2. DO NOT enclose generator any more than shown in
Figure 9.
NOTE: If a wheel kit is installed on the generator, enlarge
shelter accordingly.
Breathing carbon monoxide can cause nausea,
fainting or death.
3. Follow steps 3 through 8 as described previously in
“Creating a Temporary Shelter”.
• Operate generator ONLY outdoors.
• Keep exhaust gas from entering a confined area through
windows, doors, ventilation intakes or other openings.
• DO NOT operate generator inside any building or enclosure
(even if doors or windows are open), including the generator
compartment of a recreational vehicle (RV).
13
7500EXL Extended Life Generator
Figure 11 — 12Volt DC, 10 Amp Receptacle
GENERATOR ADAPTER
CORD SET
The generator is equipped with a 25’ generator adapter cord
set designed for a 240Volt, 30 Amp grounded neutral circuit
(Figure 10).The generator adapter cord set provides a
convenient supply of emergency power into your dwelling so
that your generator can be operated safely outside.
This receptacle can not recharge 6Volt batteries and can
not be used to crank an engine having a discharged battery.
See the section “Charging a Battery” (page 11) before
attempting to recharge a battery.
Figure 10 — Generator Adapter Cord Set
120Volt AC, 20 Amp, Duplex
Receptacle
Each receptacle (Figure 12) is protected against overload by
a 20 Amp push–to–reset circuit breaker.
Figure 12 — 120Volt AC, 20 Amp, Duplex Receptacle
The maximum load on each outlet is 20 Amps.The
maximum total load on both yellow wire outlets or both
black wire outlets is 30 Amps.
NOTE: Follow all safety precautions when connecting any
extension cord or device to the generator.
RECEPTACLES
Use each receptacle to operate 120Volt AC, single–phase,
60 Hz electrical loads requiring up to 2,400 watts (2.4 kW)
at 20 Amps of current. Use cord sets that are rated for
125Volt AC loads at 20 Amps (or greater).
CAUTION
Receptacles may be marked with rating value greater
than generator output capacity.
• NEVER attempt to power a device requiring more amperage
than generator or receptacle can supply.
120Volt AC, 30 Amp Locking
Receptacle
• DO NOT overload the generator. See “Don’t Overload
Generator”.
Use a NEMA L5–30 plug with this receptacle. Connect a
3–wire cord set rated for 125Volt AC loads at 30 Amps to
the plug (Figure 13).
12Volt DC, 10 Amp Receptacle
This receptacle allows you to recharge a 12Volt
automotive or utility style storage battery with the battery
charge cables provided (Figure 11).
14
7500EXL Extended Life Generator
Figure 13 — 120Volt AC, 30 Amp, Locking Receptacle
3-Wire Cord Set
120/240Volt AC, 50 Amp Receptacle
Use a NEMA 14–50 plug with this receptacle (Figure 15).
Connect a 4-wire cord set rated for 250Volt AC loads at
50 Amps to the plug.
NEMA L5-30
Neutral
120V
Hot
Figure 15 — 120/240Volt AC, 50 Amp Receptacle
240Volts AC
Frame Ground
Ground (Green)
Use this receptacle to operate 120Volt AC, 60 Hz, single
phase loads requiring up to 3,600 watts (3.6 kW) of power
at 30 Amps.The outlet is protected by a 30 Amp
push–to–reset circuit breaker.
Y (Hot)
X (Hot)
120/240Volt AC, 30 Amp, Locking
Receptacle
Use a NEMA L14–30 plug with this receptacle. Connect a
4–wire cord set rated for 250Volt AC loads at 30 Amps (or
greater) (Figure 14).You can use the same 4–wire cord if
you plan to run a 120Volt load.
120Volts
AC
120Volts
AC
W (Neutral)
Figure 14 — 120/240Volt AC, 30 Amp Receptacle
4-Wire Cord Set
NEMA 14-50
Use this receptacle to operate 120/240Volt AC, 60 Hz,
single phase loads requiring up to 7,500 watts (7.5 kW) of
power.The outlet is protected by a 35 Amp push–to–reset
circuit breaker.
240V
120V
120V
W (Neutral)
X (Hot)
Ground (Green)
Y (Hot)
NEMA L14-30
This receptacle powers 120/240Volt AC, 60 Hz, single
phase loads requiring up to 3,600 watts of power at
30 Amps for 120Volts; 7,200 watts of power (7.2 kW) at
30 Amps for 240Volts.The outlet is protected by a 30 Amp
push–to–reset circuit breaker.
15
7500EXL Extended Life Generator
4. Plug in and turn on the next load.
5. Again, permit the generator to stabilize.
6. Repeat steps 4 and 5 for each additional load.
NEVER add more loads than the generator capacity.Take
special care to consider surge loads in generator capacity,
as described above.
DON'T OVERLOAD
GENERATOR
Capacity
You must make sure your generator can supply enough
rated (running) and surge (starting) watts for the items you
will power at the same time. Follow these simple steps:
Figure 16 - Wattage Reference Chart
Additional
Surge
(Starting)
Watts
Rated*
(Running)
Watts
Tool or Appliance
Essentials
1. Select the items you will power at the same time.
2. Total the rated (running) watts of these items.This is
the amount of power your generator must produce to
keep your items running. See Figure 16.
Light Bulb - 75 watt
Deep Freezer
Sump Pump
Refrigerator/Freezer - 18 Cu. Ft.
Water Well Pump - 1/3 HP
Heating/Cooling
Window AC - 10,000 BTU
Window Fan
Furnace Fan Blower - 1/2 HP
Kitchen
Microwave Oven - 1000 Watt
Coffee Maker
Electric Stove - Single Element
Hot Plate
Family Room
DVD/CD Player
VCR
Stereo Receiver
Color Television - 27”
Personal Computer w/17” monitor
Other
75
500
800
800
1000
-
3. Estimate how many surge (starting) watts you will
need. Surge wattage is the short burst of power
needed to start electric motor-driven tools or
appliances such as a circular saw or refrigerator.
Because not all motors start at the same time, total
surge watts can be estimated by adding only the
item(s) with the highest additional surge watts to the
total rated watts from step 2.
500
1200
1600
2000
1200
300
800
1800
600
1300
Example:
Rated (Running)
Watts
Additional Surge
(Starting) Watts
1800
1000
1500
1500
2500
-
-
-
-
Tool or Appliance
Window Air
Conditioner
Refrigerator
Deep Freezer
Television
1200
800
500
500
1600
500
-
-
100
100
450
500
800
-
-
-
-
-
Light (75 Watts)
75
3075 Total
Running Watts
1800 Highest
Surge Watts
Total Rated (Running) Watts
Highest Additional Surge Watts
= 3075
= 1800
Security System
180
300
480
-
-
AM/FM Clock Radio
Garage Door Opener - 1/2 HP
Electric Water Heater - 40 Gallon
DIY/Job Site
Total Generator Output Required = 4875
520
-
4000
Power Management
To prolong the life of your generator and attached devices,
it is important to take care when adding electrical loads to
your generator.There should be nothing connected to the
generator outlets before starting it's engine.The correct
and safe way to manage generator power is to sequentially
add loads as follows:
1. With nothing connected to the generator, start the
engine as described in this manual.
2. Plug in and turn on the first load, preferably the largest
load you have.
Quartz Halogen Work Light
Airless Sprayer - 1/3 HP
Reciprocating Saw
Electric Drill - 1/2 HP
Circular Saw - 7 1/4”
Miter Saw - 10”
Planer/Jointer - 6”
Table Saw/Radial Arm Saw - 10”
Air Compressor - 1-1/2 HP
1000
600
960
1000
1500
1800
1800
2000
2500
-
1200
960
1000
1500
1800
1800
2000
2500
*Wattages listed are approximate only. Check tool or
appliance for actual wattage.
3. Permit the generator output to stabilize (engine runs
smoothly and attached device operates properly.
16
7500EXL Extended Life Generator
NOTE: DO NOT use a garden hose to clean generator.
SPECIFICATIONS
Water can enter engine fuel system and cause problems. In
addition, if water enters generator through cooling air slots,
some of the water will be retained in voids and cracks of
the rotor and stator winding insulation.Water and dirt
buildup on the generator internal windings will eventually
decrease the insulation resistance of these windings.
Starting Wattage . . . . . . . . . . . . . . . . . . . . . .13,500 watts
Wattage . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7,500 watts
AC Load Current:
At 120Volts . . . . . . . . . . . . . . . . . . . . . . . . .62.5 Amps
At 240Volts . . . . . . . . . . . . . . . . . . . . . . . . .31.2 Amps
Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–phase
Rated Frequency . . . . . . . . . . . . . . . . . . . . . . . . .60 Hertz
Fuel Tank Capacity . . . . . . . . . . . . . . . . . . . . 7 U.S. gallons
Shipping Weight . . . . . . . . . . . . . . . . . . . . . . . . . .240 lbs.
WARNING
Unintentional sparking can result in fire or
electric shock.
GENERAL MAINTENANCE
RECOMMENDATIONS
The Owner/Operator is responsible for making sure that
all periodic maintenance tasks are completed on a timely
basis; that all discrepancies are corrected; and that the unit
is kept clean and properly stored. NEVER operate a
damaged or defective generator.
WHEN ADJUSTING OR MAKING REPAIRSTOYOUR
GENERATOR
• Disconnect the spark plug wire from the spark plug and place
the wire where it cannot contact spark plug.
WHENTESTING FOR ENGINE SPARK
• Use approved spark plug tester.
• DO NOT check for spark with spark plug removed.
NOTE: Should you have questions about replacing
components on your Generac Portable Products generator,
please call 1-800-270-1408 for assistance.
Battery Maintenance
Other than float charging, described elsewhere, no
maintenance is required for the battery. Keep the battery
and terminals clean and dry.
Engine Maintenance
See engine operator’s manual for instructions.
IMPORTANT: Battery charging should be performed in a
dry location, such as inside a garage.
CAUTION
Avoid prolonged or repeated skin contact with used
To Clean the Generator
• Use a damp cloth to wipe exterior surfaces clean.
motor oil.
• Used motor oil has been shown to cause skin cancer in
certain laboratory animals.
CAUTION
Improper treatment of generator can damage it and
shorten its life.
• Thoroughly wash exposed areas with soap and water.
KEEP OUT OF REACH OF CHILDREN. DON'T
POLLUTE. CONSERVE RESOURCES. RETURN
USED OIL TO COLLECTION CENTERS.
• DO NOT expose generator to excessive moisture, dust, dirt,
or corrosive vapors.
• DO NOT insert any objects through cooling slots.
• Use a soft bristle brush to loosen caked on dirt or oil.
• Use a vacuum cleaner to pick up loose dirt.
Generator Maintenance
• Use low pressure air (not to exceed 25 psi) to blow
away dirt. Inspect cooling air slots and opening on
generator.These openings must be kept clean and
unobstructed.
Generator maintenance consists of keeping the unit clean
and dry. Operate and store the unit in a clean dry
environment where it will not be exposed to excessive
dust, dirt, moisture or any corrosive vapors. Cooling air
slots in the generator must not become clogged with snow,
leaves or any other foreign material.
17
7500EXL Extended Life Generator
Engine Storage
STORAGE
See engine operator’s manual for instructions.
The generator should be started at least once every seven
days and allowed to run at least 30 minutes. If this cannot
be done and you must store the unit for more than
30 days, use the following guidelines to prepare it for
storage.
Other StorageTips
• To prevent gum from forming in fuel system or on
essential carburetor parts, add fuel stabilizer into fuel
tank and fill with fresh fuel. Run the unit for several
minutes to circulate the additive through the carburetor.
The unit and fuel can then be stored for up to
Generator Storage
• Clean the generator as outlined in “To Clean the
Generator.”
24 months. Fuel stabilizer can be purchased locally.
• DO NOT store fuel from one season to another unless
it has been treated as described above.
• Check that cooling air slots and openings on generator
are open and unobstructed.
• Replace fuel container if it starts to rust. Rust and/or dirt
in fuel can cause problems if it's used with this unit.
WARNING
Storage covers can be flammable.
• Store unit in a clean and dry area.
• DO NOT place a storage cover over a hot generator.
• Let equipment cool for a sufficient time before placing the
cover on the equipment.
18
7500EXL Extended Life Generator
TROUBLESHOOTING
Problem
Cause
Correction
1. One of the circuit breakers is open.
2. Fault in generator.
1. Reset circuit breaker.
2. Contact Generac service facility.
No AC output is available,
but engine is running.
3. Poor connection or defective cord set. 3. Check and repair.
4. Connected device is bad.
4. Connect another device that is in
good condition.
1. Short circuit in a connected load.
2. Generator is overloaded.
1. Disconnect shorted electrical load.
2. See "Don't Overload Generator".
3. Contact Generac service facility.
Engine runs good at no-
load but "bogs" down"
when loads are connected.
3. Shorted generator circuit.
1. Fuel valve is in the "Off" position.
2. Failed battery.
1. Turn fuel valve to "On" position.
2. Replace battery.
Engine will not start; or
starts and runs rough.
Engine shuts down during
operation.
Out of gasoline.
Load is too high.
Fill fuel tank.
Engine lacks power.
See "Don't Overload Generator".
19
GENERAC PORTABLE PRODUCTS OWNER EQUIPMENT WARRANTY POLICY
Effective November 1, 2004
LIMITED WARRANTY
"Generac Portable Products is a licensed trademark of Briggs & Stratton Power Products. Briggs & Stratton Power Products will
repair or replace, free of charge, any part, or parts of the equipment** that are defective in material or workmanship or both.
Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser.This
warranty is effective for the time periods and subject to the conditions provided for in this policy. For warranty service, find your
nearest Authorized service dealer by calling 1-800-270-1408.Warranty service may only be performed by a Briggs & Stratton
Power Products Authorized service dealer.
THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE,ARE LIMITED TO THE TIME PERIOD SPECIFIED, OR TO THE EXTENT PERMITTED
BY LAW.ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED. LIABILITY FOR CONSEQUENTIAL DAMAGES UNDER
ANY AND ALL WARRANTIES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some countries or
states do not allow limitations on how long an implied warranty lasts, and some countries or states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you.This warranty gives
you specific legal rights and you may also have other rights that vary from country to country or state to state.”
WARRANTY PERIOD*
PRODUCTS**
Pressure Washer
Portable Generator
CONSUMER USE
1 year
COMMERCIAL USE
90 days
2 years (2nd year parts only)
1 year
* The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the
period of time stated in the table above. "Consumer use" means personal residential household use by a retail consumer.
"Commercial use" means all other uses, including use for commercial, income producing or rental purposes. Once equipment has
been used commercially, it shall thereafter be considered to be in commercial use for purposes of this warranty.
** The engine and starting batteries are warranted solely by the manufacturers of those products.
WARRANTY REGISTRATION IS NOT NECESSARYTO OBTAINWARRANTY ON BRIGGS & STRATTON POWER
PRODUCTS EQUIPMENT.SAVEYOUR PROOF OF PURCHASE RECEIPT.IFYOU DO NOT PROVIDE PROOF OFTHE
INITIAL PURCHASE DATEATTHETIMEWARRANTY SERVICE IS REQUESTED,THE MANUFACTURING DATE OFTHE
EQUIPMENTWILL BE USEDTO DETERMINETHEWARRANTY PERIOD.
About your equipment warranty:
We welcome warranty repair and apologize to you for being inconvenienced.Any Authorized service dealer may perform warranty
repairs. Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For
example, warranty service would not apply if equipment damage occurred because of misuse, lack of routine maintenance, shipping,
handling, warehousing or improper installation. Similarly, the warranty is void if the manufacturing date or the serial number on the
equipment has been removed or the equipment has been altered or modified. During the warranty period, the Authorized service
dealer, at its option, will repair or replace any part that, upon examination, is found to be defective under normal use and service.This
warranty will not cover following repairs and equipment:
• Normal Wear: Outdoor power equipment, like all mechanical devices, needs periodic parts, service and replacement to perform
well.This warranty does not cover repair when normal use has exhausted the life of a part or the equipment.
• Installation and Maintenance:This warranty does not apply to equipment or parts that have been subjected to improper or
unauthorized installation or alteration and modification, misuse, negligence, accident, overloading, overspeeding, improper
maintenance, repair or storage so as, in our judgment, to adversely affect its performance and reliability.This warranty also does not
cover normal maintenance such as adjustments, fuel system cleaning and obstruction (due to chemical, dirt, carbon or lime, etc.).
• Other Exclusions: Also excluded from this warranty are wear items such as quick couplers, oil gauges, belts, o-rings, filters,
pump packing, etc., pumps which have been run without water supplied or damage or malfunctions resulting from accidents,
abuse, modifications, alterations, or improper servicing or freezing or chemical deterioration.Accessory parts such as guns,
hoses, wands and nozzles are excluded from the product warranty.This warranty excludes failures due to acts of God and other
force majeure events beyond the manufacturers control.Also excluded is used, reconditioned, and demonstration equipment;
equipment used for prime power in place of utility power and equipment used in life support applications.
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC
JEFFERSON,WISCONSIN, U.S.A.
|